# UV-K5 V3 emulator Runs Quansheng UV-K5 V3 / UV-K1 firmware on a PC. The radio uses a Puya PY32F071 (Cortex-M0+), which QEMU has no machine for, so this adds one. The firmware boots to its main loop in about five seconds and the LCD contents are readable. Keypresses reach the firmware's scan but are not yet acted on -- see [Status](#status). ## What it is for Editing firmware and reflashing a radio to test one line is slow, and some bugs are invisible from the outside. A recent example: CW macro recording appeared to do nothing, and the cause was three layers down -- the keyer was being torn down by a later call that recomputed its state from the wrong VFO. On hardware you see "nothing happens"; here you can read the actual variables. What it does **not** do is model radio behaviour. It reproduces what the firmware *commanded* -- frequency, power step, carrier keying in time -- not the analogue result. Keying envelopes, spurious emissions and sensitivity need a real radio and a spectrum analyser. That is not a gap to be closed later; the transceiver chip has no public datasheet, so its driver is the only specification available. ## Status | Area | State | | --- | --- | | Boot to main loop | works, ~5 s | | LCD contents | readable via `tools/screenshot.py` | | SPI flash, settings, calibration | works | | Keypad matrix | rows reach the firmware's scan (`KEYBOARD_Poll` returns the right key code) but the UI does not react — under investigation | | Timing accuracy | deliberately wrong, see [Timing](#timing) | | Radio/RF behaviour | not modelled | ## Layout qemu/ QEMU sources to be copied into a QEMU tree py32f071.c the SoC and machine (the bulk of the work) armv7m_systick.*.patched SysTick with the poll-boost property added assets/ calibration.bin 512-byte dump from a real radio tools/ run, screenshot, inject keys, probe state harness/, stubs/, shim/, tests/ host build of the CW timing chain (stage A) ## Building Needs a QEMU 7.2 source tree, `meson`, `ninja`, `libfdt-dev`, `libglib2.0-dev`, `libpixman-1-dev`. # 1. Drop the sources into a QEMU tree cp qemu/py32f071.c $QEMU/hw/arm/ cp qemu/armv7m_systick.c.patched $QEMU/hw/timer/armv7m_systick.c cp qemu/armv7m_systick.h.patched $QEMU/include/hw/timer/armv7m_systick.h # 2. Register the machine. In $QEMU/hw/arm/Kconfig: # config UVK5_V3 # bool # default y # depends on TCG && ARM # select PY32F071_SOC # config PY32F071_SOC # bool # select ARM_V7M # select UNIMP # In $QEMU/hw/arm/meson.build: # arm_ss.add(when: 'CONFIG_UVK5_V3', if_true: files('py32f071.c')) # 3. Build just the ARM target cd $QEMU ./configure --target-list=arm-softmmu --disable-docs --disable-tools cd build && ninja qemu-system-arm ## Running python3 tools/make_flash.py # once, builds assets/flash.img tools/run.sh # starts the machine tools/where.sh # where the firmware is executing python3 tools/screenshot.py --frame-addr 0x200013DC \ --status-addr 0x2000175C --port 1234 --out screen.png python3 tools/key.py MENU # inject a keypress tools/gpiob_dump.sh # GPIOB registers The machine exposes a GDB stub on port 1234 and a QMP socket at `/tmp/uvk5-qmp.sock`. It is headless: the screen is read out of guest memory rather than drawn, so no display backend is needed. Screenshots need the addresses of `gFrameBuffer` and `gStatusLine`, which move between builds. Find them with: arm-none-eabi-nm firmware.elf | grep -E 'gFrameBuffer|gStatusLine' ## How the machine is put together Register layouts come from the vendor CMSIS header shipped with the firmware (`Drivers/CMSIS/Device/PY32F071/Include/py32f071xB.h`), not from guesswork. FLASH 0x08000000 128 KB application at +0x2800, bootloader below it SRAM 0x20000000 16 KB RCC 0x40021000 GPIO 0x50000000 ports A, B, C, F at 0x400 intervals SPI1 0x40013000 display SPI2 0x40003800 flash ADC1 0x40012400 Modelled: RCC, GPIO, ADC, both SPI controllers, DMA1, and the PY25Q16 flash. Everything else answers through a logging catch-all — the log is how the next thing worth modelling gets identified. Seven things had to be right before the firmware would boot, each found by watching where it stopped: - **Flash alias at the application offset.** The core fetches its vector table from address 0, and the image loads at 0x08002800, so 0 has to alias there and not at the flash base. - **Clock ready bits.** `BOARD_Init` polls them; each enable bit is mirrored into its ready bit. - **ADC calibration.** `CR2.CAL` is write-1-to-start and hardware-cleared, so it must never be stored set or the wait loop never exits. - **SPI flags.** Transfers complete inside the register write, so TXE stays asserted and RXNE is raised by the write. - **DMA.** The flash driver never touches the SPI data register — it arms channels 4 and 5, enables the transfer-complete interrupt and spins on a flag its ISR sets. - **SysTick.** See below. - **Transceiver data line.** `RADIO_SetupRegisters` waits for bit 0 of the BK4819 REG_0C to clear. The bus is bit-banged over GPIO, so PB9 idles low until that bus has a real model, making reads return zero. ## Timing `SYSTICK_DelayUs` polls the SysTick counter and accumulates differences. On hardware each loop iteration advances the counter by tens of ticks; under emulation a register read costs far more relative to guest time, so the counter barely moves per read. Measured: a 120 ms delay advanced 832 of 5,760,000 required ticks in four seconds — about 7.7 hours to complete. Lowering the clock does not help, which is worth knowing before trying it: the bottleneck is loop iterations per second, not counter speed. Dropping 48 MHz to 200 Hz gained only 32x. What works is reporting a counter value that runs ahead of the real one, growing with every read. The `poll-boost` property on SysTick does that. Two earlier attempts wrote the value back into the timer instead, which made each read re-anchor the count — the reported value stopped changing, the firmware's `if (cur != prev)` guard never fired, and the loop hung outright. The consequence is that guest time runs fast during any delay. Fine for exercising menus and control flow; wrong for judging signal timing. ## Stage A: the CW timing chain on the host `harness/`, `stubs/`, `shim/` and `tests/` compile `app/cwkeyer.c` and `app/cwmacro.c` unmodified against stub drivers, with a virtual clock and scripted paddle input. Feed a timeline of contact closures, assert on the decoded characters and element durations. Firmware sources are compiled as-is on purpose. Editing them to make them build on a host would let the tests drift from what the radio runs. The debounce in `CW_ReadKeys` is transcribed rather than stubbed, because its asymmetry (three consecutive reads to register a press, immediate release) is part of the timing behaviour under test. ## Credits Base firmware: [armel/uv-k1-k5v3-firmware-custom](https://github.com/armel/uv-k1-k5v3-firmware-custom). Register definitions from the vendor CMSIS headers.