The ladder conflated two variables -- every small test app spun first, every big one called the firmware immediately. Separated, all measured with the 2 ms PC probe on the page's own emulator: a 3028-byte app that calls nothing loops in the overlay indefinitely (1704 samples, all inside its first 512 bytes), so blob size is not the problem; adding one print_tiny changes nothing (2039 samples, with 1024 font-region reads in the flash log, the first at 0x1e0000), so the font path and the sector-cache worry are both fine; adding get_key as well still runs (2029 samples); adding display_clear too still runs (1978 of 13195 samples inside the app).
So the three calls no surviving app had ever made are harmless, and the API surface Minesweeper uses is covered. Its failure is its own bug; the next step is an ordinary bisect of its draw() path through the page.
Measured with the 2 ms PC probe: Spin (16 B) loops in the overlay forever; Delay (248 B) is still running 13 s later, 54 of the last 60 samples at 0x20000348; Phases (372 B) survives bar, blit and led; Ladder (544 B) dies before drawing; Minesweeper (2408 B, and 2428 B with an opening spin) is dead within about 4 ms either way. An opening spin does not save the big apps, so the difference is how much of the app has been copied rather than when the first call is made -- and that also explains why Tetris's full 3300 bytes were present in the overlay when checked afterwards: the copy finishes after the app has been entered.
Same family as the four flash bugs already recorded here: the loader is told the transfer is over while the guest is still feeding it. Next: watch the SPI/DMA busy and complete flags during a large read instead of reasoning about them.
uvk5_pc_probe_interval_ms() reads UVK5_PC_PROBE_MS and falls back to 100, so existing probe runs are unchanged. At 2 ms a launch gives 468 samples in about 0.94 s and exactly one of them is inside the 4 KiB overlay: the app lives for roughly 2 ms, not 100.
The trace settles two things and adds one. The loader copies and jumps (the single overlay sample; a 16-byte app that calls nothing stays there forever). The sector-cache overwrite is dead: the flash log's last transaction for the run is the app's own code load (addr=103000 len=2408) and nothing follows it, no font read included. New: after the app dies the firmware loops inside its own flash (PCs near 0x08005118/0x08005122/0x08005248) with zero flash reads and no key response at all -- F then 7 no longer opens the menu and an explicit MENU down/up changes nothing -- so the launcher or its fault path is wedged.
The flash probe records every transaction in order and the last one for that launch is the app's own code load (addr=103000 len=544, first bytes f0b583b0); nothing follows before the app is gone, so no font or resource read lands on the running app in that window. The 7848 font-region reads in the log belong to the firmware's own repainting.
What stands measured: the loader copies and jumps (a PC sample lands in the overlay, and a 16-byte app that calls nothing loops there forever); the app dies well under 100 ms (panel reads at t+113 ms still show the menu, at t+193 ms only the launcher's title box); an app that spins first survives a bar, a blit and led and dies around delay_ms; one that calls blit immediately is gone before it can be seen. Next: drop the PC probe interval from 100 ms to a couple of milliseconds, which is a one-line model change and turns it into a real trace of the app's short life.
Measured on the page's emulator with UVK5_PC_PROBE and UVK5_FLASH_PROBE inherited through its own launcher, so the instance measured is the one that draws. Spin (16 bytes, calls nothing) sits at 0x20000286 in 42 of 383 PC samples after MENU: it loops in the overlay forever, so the loader works. Minesweeper (2408 bytes) is loaded -- the only big flash read is 0x109000 len 2408, first bytes its own -- and a single PC sample catches it inside the overlay before it is gone: it lives well under 100 ms. Phases (372 bytes) draws a progress bar straight into the framebuffer between calls, and the bars for framebuffer-only and led are on screen while the bar after delay_ms never appears.
The overlay is the PY25Q16 sector cache (app_overlay.h says so), so a service reading the external flash -- the font table is at 0x1E0000 -- lands on top of the running app. Real hardware cannot behave that way, since upstream's own apps call print_tiny, so the firmware must gate the sector cache while an app is loaded; that gate is what the model is missing. Next: find it in the flash driver and check what the model answers.
With the pristine dump restored the page draws (485 lit bytes) and answers 0x0730 with four committed apps. Driving its /api/key and reading its /api/panel: F then 7 opens the menu (ink 1810 -> 1976), DOWN x3 moves the selection (1976 -> 1832), MENU on the app row drops the screen to the title box alone (1832 -> 210) after which MENU, DOWN, UP and F change nothing, and EXIT brings the menu back (1832). So the launcher is entered and left, and the app neither draws nor reads keys.
This supersedes the inconclusive PC measurements taken on hand-started QEMU instances, which came up without a picture while the page's instance draws. Recorded in both AGENTS files: restore work/user-flash.img before testing (the copy carrying the adopted FMP3 marker, image_crc32 0x9d27c3db rather than 0x4d87ce48, comes up blank and makes keys dead, which earlier rounds mistook for the app failing), and measure through the page rather than a hand-started emulator.
Hand-started QEMU instances all came up with a blank panel (0 lit pixels) while the page's own instance draws (803), same image and a different firmware file, so 'the PC never entered the overlay' was measured on a radio that never reached its main loop and is inconclusive rather than a finding.
Driving the page's own /api/key and reading /api/panel reproduces what the user sees: F, 7, DOWN x3 and MENU all answer ok and the screen does not change by a pixel (ink 232 throughout). The page's firmware.bin is 109.3 KiB and the Labs build that does open the app menu is 111.9 KiB -- a different build. The radio still answers 0x0730 with four committed apps, so it supports the app region but has no F+7 entry. Testing an overlay app requires running the Labs build, and measuring through the page rather than a hand-started QEMU.
Measured by polling the PC over QMP every 30 ms, finer than the model's own 100 ms probe. After launching Tetris the overlay at 0x20000280 holds Tetris's code byte for byte, so the loader's copy is correct and aligned; the earlier claim in this session that it was shifted by one byte was my own parsing dropping the first value. But 172 PC samples over 4.5 s and 64 more over 2 s were all inside firmware flash at 0x08013260, a wait loop, and none landed in the overlay. A 16-byte app that calls nothing behaves identically, and Breakout's header is field-for-field the shape of ours, so neither the app's code nor its header is the reason. The failure is upstream of the app, which makes the earlier 'Tetris runs' note stale: per this file's own rule it is treated as unverified until it reproduces.
Also carries the CI-fix branch merge and a regression test for _edit_flash creating its working-copy directory (its fixture image has to be a real size: slot 0 sits at 0x102000).
pip install ziglang cross-compiles to thumb-freestanding-eabi, which is enough to build a .app with no arm-none-eabi-gcc and no Docker. Measured refusals: --defsym, -Ttext and --section-start come back as unsupported linker args, so the VMA is resolved into a copy of app.ld; -T is forwarded (a missing script errors); --image-base is accepted but page-aligns the segments into 0x200103C8 and 0x20020C94. tools/elf2bin.py extracts allocated sections rather than program headers, because lld maps the ELF header and phdr table as a 180-byte LOAD of its own -- following the headers starts the image at 0x20000000 and APP_ERR_VMA. One division pulled in __aeabi_uidiv, which a -nostdlib blob cannot have: Minesweeper now avoids division entirely. app_main carries the .text.entry attribute upstream's apps use, so the entry is first for the loader's jump to offset 0.
Minesweeper builds to 2408 bytes of code against a 4096-byte budget. Installed through the page, the firmware reads the slot header twice and then exactly code_size bytes from slot+0x1000 -- the only read of that size in the boot log -- so the blob shape, header, CRC, VMA and offset are all accepted. Whether control reaches the overlay is unproven: the 100 ms PC probe saw no overlay address, no APP ERROR screen appears, and the app does not draw. test_elf2bin pins the phantom-header-segment lesson; both AGENTS files record the rest.
The blank screen was self-inflicted and the earlier explanation was wrong. The FMP3 marker at 0x100000 is an ordinary state record -- generation, image_size, image_crc32, firmware_slot/slot_inv, config_bank/bank_inv and a matching state_crc32 (0x661286F1) -- not a pending flag. What actually happened: a firmware uploaded over a state that recorded a different identity made the firmware take the restore/adopt path, which draws nothing (panel 1024/1024 bytes zero) while the serial banner printed normally. Restoring the untouched dump fixed it at once (485/1024 bytes lit) and the three apps reinstalled and were confirmed by 0x0730.
Clearing the marker sectors was tried twice (a whole 8 KiB, then just the 24-byte headers) and is not a fix: it sends the firmware down MB_MARK_MISSING = fresh radio, which adopts the running firmware slowly and without drawing, and its own write-back restores the marker anyway. AGENTS.md and AGENTS.zh-CN.md now say so in place of the wrong claim.
apps/minesweeper/ adds our own 9x9 minesweeper for the 4 KiB overlay: no left/right keys exist on this radio (so the cursor walks with UP/DOWN and digits pick a row then a column), 81 cells need three 9-byte bit arrays rather than a uint16_t mask (the uint16_t version compiled fine and was wrong past cell 15), mines are placed after the first reveal so it cannot lose immediately, and the source compiles clean under gcc -Wall -Wextra -Werror against upstream's real app_api.h. It has not been built for ARM or run -- no toolchain here -- and the README says so.
A real image whose 0x100000 marker held FMP3 next to a committed slot 0 made the factory bootloader reflash the internal flash from that slot on every power-on: the serial banner reappeared once a cycle (7 -> 8 in 25 s) while the screen never changed. Clearing the two marker sectors (0x100000..0x101FFF, stopping just before the app region at 0x102000) ended it, and the radio booted once and stayed.
It also explained why page-side installs vanished: the emulator writes its in-memory image back on exit, and the looping guest's copy was older than the file, so powering it off overwrote the installs. With the loop gone the same installs survive a power cycle -- installed, powered off, still listed, powered on, still listed, and 0x0730 answered with all three. Both notes are in AGENTS.md and AGENTS.zh-CN.md; work/app-template/ got a starter app, its README and the upstream api/ld it needs (git-ignored).
F then 7 opens the F4HWN APPS menu and MENU runs the selection -- upstream's own wording in UVStudio's locales/en.js, and what App/apps/app_menu.c does: KEY_MENU on an installed row calls APP_LaunchOverlay, which runs until the app exits; EXIT leaves the menu. The page's hint now says it too.
Recorded with it: twenty keys short and long, the whole 79-entry settings menu and the multiboot menu all left the app region untouched (the multiboot menu reads firmware slots, not apps), and the way in turned out to be written in the flasher's translation file rather than the firmware source. When a feature's entry point is missing, the host tool that installs it is the document.
GET /api/apps/radio opens the firmware's serial port and sends 0x0730 for all sixteen slots, so the answer comes from the running firmware rather than from our reading of the file -- which is the check that matters, because the bytes can be right and the firmware still refuse a slot. Measured through the page after installing Beam.app into slot 0: slot 0 -> Beam 1.0, 1100 B, crc 0xd976058, shortcut beam, committed; slots 1..3 -> status 2 with unrelated data, the resource-block overlap the install guard refuses. A button beside the table asks it and shows the answer in its own column.
The server gives its own emulator a serial port (--serial-port, default 4445) and uvk5_slots_serial.Radio gained a public app_info(slot), so nothing reaches into a private helper. uvk5_apps.parse_radio_reply decodes the answer and is tested without a radio. Also recorded: QEMU needs the mingw64 DLLs on PATH, and started by hand without them it exits before opening QMP, which surfaces only as 'QMP socket never appeared'.
UVStudio's own js/flash.js names the protocol: MSG_APP_INFO 0x0730/0x0731, MSG_APP_ERASE 0x0732/0x0733, MSG_APP_WRITE 0x0734/0x0735, MSG_APP_VALIDATE 0x0736/0x0737, with APP_SLOT_COUNT 16, APP_IMG_OFFSET 0x1000, APP_HDR_SIZE 64 and APP_MAGIC 0x31504146 -- the constants this page already used. It uses slots 0..7 and labels them 1..8, and writes the header last so a partial write cannot validate; the page now labels slots the same way.
The Labs build answers 0x0730 over USART, so an installed Beam.app was queried on the radio: slot 0 came back status 0 with the header this page wrote (FAP1, code_size 1100, CRC 0x0d976058, flags 0x0801, name Beam), which confirms the region, the offset and the layout from the firmware's side rather than from a header I read. Slots 1 and 2 answered status 2 with unrelated data -- the overlap the install guard refuses to overwrite.
The English line about the page's app table went in with the previous commit; the Chinese one did not, because the sentence it anchors to wraps mid-phrase and the marker I used did not match. Added, so the pair says the same thing again.
The Labs edition's apps live in the external flash, in the region its own App/apps/app_overlay.h defines (16 slots of 8 KiB from 0x102000, a 64-byte FAP1 header at the slot base, code one 4 KiB sector later), and upstream installs them from UVStudio over WebSerial. The page owns the image, so this adds GET /api/apps, POST /api/apps/<n> and POST /api/apps/<n>/erase, which put the same bytes at the same offsets with no serial protocol and no browser permission.
Measured on a real image while wiring it up: every one of the 16 slots already held data that is neither empty nor an app -- the localised build's factory resource block overlaps 0x102000 -- so install now refuses to overwrite anything that is not an app unless asked (--force, ?force=1), naming what is there. And _edit_flash edits a copy, which is why the source image shows no changed bytes; the first test read that as 'the install did nothing' and now checks FlashSlot.path. Tests: test_uvk5_apps grew to 20, test_webui.TestAppEndpoints adds 7 over the endpoints.
The Labs edition runs overlay apps (Tetris, Breakout, Plasma, Cube3D, Beam, Beacon, FoxHunt, BroadcastFM) that upstream UVStudio installs over WebSerial. This page owns the flash image, so the same bytes go to the same offsets with no serial protocol and no browser permission: APP_REGION_BASE 0x102000, APP_SLOT_STRIDE 0x2000, APP_CODE_OFFSET 0x1000, 16 slots, taken from the firmware's own App/apps/app_overlay.h rather than inferred.
tools/uvk5_apps.py parses and validates the 64-byte FAP1 header (zlib CRC-32 over the code, vma 0x20000280, name, version, capabilities), lists, installs and erases slots, and refuses what the firmware would show as APP ERROR. test_uvk5_apps covers those refusals plus install/erase/list round trips, and parses a real upstream Beam.app when one has been downloaded. The header struct was 60 bytes at first -- a missing vma field -- which the real file's bytes showed at once.
The page only knew its own input. A build called f4hwn.fusion.bin reports EGZUMER+F4HWN v6.0.0.CN, and with the multi-system release a committed external slot makes the factory bootloader reflash the internal flash from that slot on every power-on -- so the uploaded image never runs and the page keeps naming it. The firmware prints its own banner on USART1; tools/uvk5_banner.py reads it back, /api/firmware returns running: {banner, matches_uploaded, note}, and the page shows what the device reports, flagging it only when the running version is not in the uploaded image at all.
That reader also exposed a regression of my own: _start_stderr_pump had been rewritten to read the pipe in 64 KB chunks, which kept QEMU from blocking but delivered nothing to the log until 64 KB had accumulated -- and the banner is forty bytes, so it never appeared. It reads lines again, still starting before anything waits on QEMU, and test_uvk5_supervisor passes either way.
The screenshot example pasted one build's numbers and told the reader to get them with nm -- which cannot work here, because the images are program-header-only ELFs with no symbol table. It now asks the firmware through tools/uvk5_buffers.py first. The webui example drops the flags entirely, since the page draws the controller's memory and needs none.
Also fixed the paragraph in both READMEs that had a tool name and a flag on one line, which the doc checker (correctly) read as passing that flag to that tool.
The page was told --frame-addr 0x200012BE --status-addr 0x2000163E and used them as a fallback. The firmware the user actually flashed keeps its buffers at 0x2000129E/0x2000161E, 32 bytes earlier, so every line landed 32 bytes off: that is the "other firmware looks shifted" report. The images here are minimal ELFs with no symbol table, so there is nothing to read -- but the firmware's own buffers hold the same bytes the controller holds, and tools/uvk5_buffers.py finds them by matching (1024/1024 bytes for that file).
The two address flags are optional now, work/run-webui.ps1 passes no machine-specific values at all, and the page reports what it found in /api/status and /api/panel. tools/uvk5_testenv.qemu() also looks in the sibling qemu-7.2/build the rest of the repo assumes. Fixed /api/panel's emulator-off branch, which called jsonify with both a dict and kwargs and 500'd.
Tests: test_uvk5_buffers (the search must count matches, not pairs -- its first version scored every offset full marks and always answered the first one).
uvk5_stream.py used STATUS_BYTES without importing it, so the panel branch raised NameError on every frame and a bare except swallowed it: every screen the page drew came from guest RAM at one build's addresses. The pump now reports which source it used and why, webui exposes it (/api/panel and frame_source), and test_uvk5_stream asserts the panel wins when reachable and that a fallback is announced.
The ST7565 column counter wrapped at 128 instead of the controller's 132, so addresses 128..131 came back as 0..3, fell outside the col>=4 store, and were dropped: every row lost its last four pixels, which is where the battery icon lives. Pre-fix, filling a page with 0xFF left columns 124..127 blank; now they carry content and the page's frame matches the panel memory 8192/8192.
The bootloader's DFU handler is reachable only when SRAM[0x20000020] is 3, which only a program that then resets can write. The application's 0x05DD takes that path only with ENABLE_OVERLAY; this build resets straight back into the application instead. Ruled out by measurement: PTT alone, PTT+SIDE1/SIDE2, MENU, a host byte in the boot window including 0x0530, and 0x05DD.
boot-key now reads a + separated list, because the firmware's own BOOT_GetMode() needs PTT and a matrix key together for every special boot mode. Tested against all four documented combinations.
flash controller: store ACR/OPTKEYR instead of swallowing them, which is what stopped the factory bootloader from starting
slots over the firmware's own serial protocol (0x0720 family); uvk5_socket/uvk5_testenv so a fresh checkout skips instead of failing; web UI slot table and Multiboot button; quick start, CONTRIBUTING, and stop tracking firmware images and radio dumps
The remaining class of claim check_docs.py could not see: whether the commands in the
docs would actually run. A renamed or removed option is the classic form of command
rot, and the one that wastes a reader's time most directly -- they paste the line and
it fails. All 9 documented flags across screenshot.py, webui.py and restore_flash.sh
are real.
The check earned its own lesson, recorded in both languages. Its first version matched
only to the end of the line, so on a wrapped command it saw --frame-addr and nothing
after the backslash: 4 of 9 flags, and it reported a clean run. A check that silently
covers a quarter of what it claims is worse than no check, because the clean result is
believed. Continuations are joined before matching now.
Confirmed it fails when it should: renaming --frame-addr to something no tool accepts
produces two named failures and exit 1, and reverting returns it to clean.
check_docs.py now runs seven checks.
Translating everything into Chinese found four claims that had already drifted, and
none of them were caught by reading -- they were caught by comparing against source.
Proofreading does not find rot, so do the comparison mechanically and keep doing it.
tools/check_docs.py verifies that every tool a README names exists, that every test in
run_tests.sh is documented in both languages, that internal .md links resolve, that the
translation pairs have matching heading structure, that memory-map addresses match the
model's #defines, and that documented firmware file:line references still point at what
the prose claims. It runs in the quick tier of run_tests.sh, needing no emulator.
Confirmed it can actually fail, because a checker that cannot is worthless: renaming a
documented tool and deleting a heading from the Chinese side each produce one named
failure and exit 1, and reverting returns it to clean.
One thing it deliberately does not check. An early version compared firmware constants
with a regex that took the first number on a line, so `key_debounce_10ms = 20 / 10` read
as 20 and it declared the docs wrong for saying 2. The docs were right and the checker
was broken. A checker that cries wolf gets ignored, so claims it cannot verify
unambiguously are left out rather than guessed at.
Current state: 16 file:line references all accurate, 7 memory-map addresses all match,
zero broken links, all three translation pairs structurally aligned.
Full translations rather than summaries, section-for-section with the English:
README (13 sections), AGENTS.md (21), and docs/reverse-proxy.md. Each pair
cross-links to the other and says the two are kept in step, since documentation
that has silently diverged is worse than documentation that does not exist.
Verified rather than eyeballed: heading counts and order match in both pairs,
every internal .md link resolves, every tool named in either README exists, and
every test in run_tests.sh appears in both.
Translating turned up four things that were already stale in the English, which
is the honest argument for having done it this way -- a summary would not have
touched them:
- the endpoint table was missing /api/ptt, /api/power/<action> and
/api/logs, and did not mention the speaker field on /api/status
- the modelled-peripheral list omitted TIM2
- the audit table still called TIM a stub, unchanged since fdcbe80 modelled
TIM2
- neither README listed uvk5_logs.py, uvk5_stream.py, uvk5_supervisor.py or
test_kill_emulator.sh, which are part of the repo rather than scratch
The ad-hoc probe scripts are now acknowledged in one line instead of being
silently absent, and described as what they are: quick to reach for, not
polished.
Unit tests: 89 passed.
mckero